View PC755BMGS300LE_8061225.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

atmel confidential features ? 18.1specint95, estima tes 12.3 specfp95 at 400 mhz (pc755) 15.7specint95, 9specfp 95 at 350 mhz (pc745) 733 mips at 400 mhz (pc755) at 641 mips at 350 mhz (pc745) selectable bus clock (12 cpu bus dividers up to 10x) p d typical 6.4w at 400 mhz, full operating conditions nap, doze and sleep modes for power savings superscalar (3 instructions per clock cycle) two instruction + branch 4 beta byte virtual memory, 4-gbyte of physical memory 64-bit data and 32-bit address bus interface 32-kb instruction and data cache six independent execution units write-back and write-through operations f int max = 400 mhz (tbc) f bus max = 100 mhz voltage i/o 2.5v/3.3v; voltage int 2.0v description the pc755 and pc745 powerpc ? microprocessors are high-performance, low-power, 32-bit implementations of the powerpc reduced instruction set computer (risc) architecture, especially enhanced for embedded applications. the pc755 and pc745 microprocessors differ only in that the pc755 features an enhanced, dedicated l2 cache interface with on-chip l2 tags. the pc755 is a drop-in replacement for the award winning powerpc 750 microprocessor and is footprint and user software code compatible with the mpc7400 microprocessor with altivec ? tech- nology. the pc745 is a drop-in replacement for the powerpc 740 microprocessor and is also footprint and user software code compatible with the powerpc 603e micropro- cessor. pc755/745 microprocessors provide on-chip debug support and are fully jtag-compliant. the pc745 microprocessor is pin compatible with the tspc603e family. g suffix cbga360 ceramic ball grid array gh suffix hitce 360 ceramic ball grid array gs suffix ci-cga360 ceramic ball grid array with solder column interposer (sci) zf suffix pbga255 flip-chip plastic ball grid array zf suffix pbga360 flip-chip plastic ball grid array gh suffix hitce 255 ceramic ball grid array powerpc ? 755/745 32-bit risc microprocessor pc755/745 rev. 2138e?hirel?01/05
2 2138e?hirel?01/05 pc755/745 atmel confidential screening this product is manufactur ed in full compliance with: hitce cbga accordin g to atmel standards cbga + ci-cga + fc-pbga up screenings based upon atmel standards full military temperature ranges (tj = -55 c, +125 c) industrial temperature ranges (tj = -40 c, +110 c) general description simplified block diagram the pc755 is targeted for low power systems and supports power management features such as doze, nap, sleep, and dynamic power management. the pc755 consists of a processor core and an internal l2 tag combined with a dedicated l2 cache interface and a 60x bus. figure 1. pc755 block diagram additional features * time base counter/decrementer * clock multiplier * jtag/cop interface * thermal/power management * performance monitor + + fetcher branch processing btic 64-entry + x : fpscr cr fpscr l2cr ctr lr bht data mmu instruction mmu not in the pc745 ea pa + x : instruction unit unit instruction queue (6-word) 2 instructions reservation station reservation station reservation station integer unit 1 system register unit dispatch unit 64-bit (2 instructions) srs itlb (shadow) ibat array 32-kbyte i cache tags 128-bit (4 instructions) reservation station 32-bit floating-point unit rename buffers (6) fpr file 32-bit 64-bit 64-bit reservation station (2-entry) load/store unit (ea calculation) store queue gpr file rename buffers (6) 32-bit srs (original) dtlb dbat array 64-bit completion unit reorder buffer (6-entry) tags 32-kbyte d cache 60x bus interface unit instruction fetch queue l1 castout queue data load queue l2 controller l2 tags l2 bus interface unit l2 castout queue 32-bit address bus 32-/64-bit data bus 17-bit l2 address bus 64-bit l2 data bus integer unit 2
3 2138e?hirel?01/05 pc755/745 atmel confidential general parameters the following list provides a summary of the general parameters of the pc755: features this section summarizes features of the pc755?s implementation of the powerpc architecture. major features of the pc755 are as follows: branch processing unit ? four instructions fetched per clock ? one branch processed per cycle (plus resolving 2 speculations) ? up to 1 speculative stream in execution, 1 additional speculative stream in fetch ? 512-entry branch history table (bht) for dynamic prediction ? 64-entry, 4-way set associative branch target instruction cache (btic) for eliminating branch delay slots dispatch unit ? full hardware detection of dependencies (resolved in the execution units) ? dispatch two instructions to six independent units (system, branch, load/store, fixed- point unit 1, fixed-point unit 2, floating-point) ? serialization control (predispatch, postdispatch, execution serialization) decode ? register file access ? forwarding control ? partial instruction decode completion ? 6 entry completion buffer ? instruction tracking and peak completion of two instructions per cycle ? completion of instructions in program order while supporting out-of-order instruction execution, completion serialization and all instruction flow changes fixed point units (fxus) that share 32 gprs for integer operands ? fixed point unit 1 (fxu1)-multiply, divide, shift, rotate, arithmetic, logical ? fixed point unit 2 (fxu2)-shift, rotate, arithmetic, logical ? single-cycle arithmetic, sh ifts, rotates, logical ? multiply and divide support (multi-cycle) ? early out multiply technology 0.22 m cmos, six-layer metal die size 6.61 mm x 7.73 mm (51 mm 2 ) transistor count 6.75 million logic design fully-static packages pc745 surface mount 255 plas tic ball grid array (pbga) pc755 surface mount 360 plasti c ball grid array (pbga) surface mount 360 ceramic ball gr id array (ci-cga, cbga, hitce) core power supply 2v 100 mv dc (nominal; some parts support core voltages down to 1.8v; see ?recommended operating conditions (1) ? on page 16 i/o power supply 2.5v 100 mv dc or 3.3v 165 mv dc (input thresholds are configuration pin selectable)
4 2138e?hirel?01/05 pc755/745 atmel confidential floating-point unit and a 32-entry fpr file ? support for ieee-754 standard single and double prec ision floating point arithmetic ? hardware support for divide ? hardware support for denormalized numbers ? single-entry reservation station ? supports non-ieee mode for time-critical operations system unit ? executes cr logical instructions an d miscellaneous system instructions ? special register transfer instructions load/store unit ? one cycle load or store cache access (byte, half-word, word, double-word) ? effective address generation ? hits under misses (one outstanding miss) ? single-cycle unaligned access within double word boundary ? alignment, zero padding, sign extend for integer register file ? floating point internal format conversion (alignment, normalization) ? sequencing for load/store multiples and string operations ? store gathering ? cache and tlb instructions ? big and little-endian byte addressing supported ? misaligned little-endian supported ? level 1 cache structure ? 32k, 32 bytes line, 8-way set associative instruction cache (il1) ? 32k, 32 bytes line, 8-way set associative data cache (dl1) ? cache locking for both instruction and data caches, selectable by group of ways ? single-cycle cache access ? pseudo least-recently used (plru) replacement ? copy-back or write through data cache (on a page per page basis) ? supports all powerpc memory coherency modes ? non-blocking instruction and data cache (one outstanding miss under hits) ? no snooping of instruction cache level 2 (l2) cache interface (not implemented on pc745) ? internal l2 cache controller and tags; external data srams ? 256k, 512k, and 1-mbyte 2-way set associative l2 cache support ? copyback or write-through data cache (on a page basis, or for all l2) ? instruction-only mode and data-only mode. ? 64 bytes (256k/512k) or 128 bytes (1m) sectored line size ? supports flow through (register-buffer) synchronous burst srams, pipelined (register-register) synchronous burst srams (3-1-1-1 or strobeless 4-1-1-1) and pipelined (register-register) late-write synchronous burst srams ? l2 configurable to direct mapped sram interface or split cache/direct mapped or private memory ? core-to-l2 frequency divisors of 1, 1.5, 2, 2.5, and 3 supported ? 64-bit data bus
5 2138e?hirel?01/05 pc755/745 atmel confidential ? selectable interface voltages of 2.5v and 3.3v ? parity checking on both l2 address and data memory management unit ? 128 entry, 2-way set associative instruction tlb ? 128 entry, 2-way set associative data tlb ? hardware reload for tlbs ? hardware or optional software tablewalk support ? 8 instruction bats and 8 data bats ? 8 sprgs, for assistance with software tablewalks ? virtual memory support for up to 4 hexabytes (2 52 ) of virtual memory ? real memory support for up to 4 gigabytes (2 32 ) of physical memory bus interface ? compatible with 60x processor interface ? 32-bit address bus ? 64-bit data bus, 32-bit mode selectable ? bus-to-core frequency multipliers of 2x, 3x, 3.5x, 4x, 4.5x, 5x, 5.5x, 6x, 6.5x, 7x, 7.5x, 8x, 10x supported ? selectable interface voltages of 2.5v and 3.3v. ? parity checking on both address and data busses power management ? low-power design with thermal requirements very similar to pc740/750. ? selectable interface voltage of 1.8v/2.0v can reduce power in output buffers (compared to 3.3v) ? three static power saving modes: doze, nap, and sleep ? dynamic power management testability ? lssd scan design ? ieee 1149.1 jtag interface integrated thermal management assist unit ? one-ship thermal sensor and control logic ? thermal management interrupt for software regulation of junction temperature
6 2138e?hirel?01/05 pc755/745 atmel confidential pin assignments figure 2 (in part a) shows the pinout of the pc 745, 255pbga package as viewed from the top surface. part b shows the side profile of the pbga package to indicate the direction of the top surface view. figure 2. pinout of the pc745, 255 pbga package as viewed from the top surface a b c d e f g h j k l m n p r t 123 4 5678 91011121314151 6 not to scale v iew die substrate assembly encapsulant part b part a
7 2138e?hirel?01/05 pc755/745 atmel confidential figure 3 (in part a) shows the pinout of the pc755, 360 pbga packages as viewed from the top surface. part b shows the side profile of the pbga package to indicate the direction of the top surface view. figure 3. pinout of the pc755, 360 pbga, cbga and ci-cga packages as viewed from the top surface a b c d e f g h j k l m n p r t 123 4 5678 91011121314151 6 not to scale 17 18 19 u v w v iew die substrate assembly encapsulant part b part a
8 2138e?hirel?01/05 pc755/745 atmel confidential pinout listings table 1 provides the pinout listing for the pc745, 255 pbga package. table 1. pinout listing for the pc745, 255 pbga package signal name pin number active i/o i/f voltages supported (1) 1.8v/2.0v 3.3v a[0 - 31] c16, e4, d13, f2, d14, g1, d15, e2, d16, d4, e13, g2, e15, h1, e16, h2, f13, j1, f14, j2, f15, h3, f16, f4, g13, k1, g15, k2, h16, m1, j15, p1 high i/o ? ? aack l2 low input ? ? abb k4 low i/o ? ? ap[0 - 3] c1, b4, b3, b2 high i/o ? ? artry j4 low i/o ? ? avdd a10 ? ? 2v 2v bg l1 low input ? ? br b6 low output ? ? bvsel (3)(4)(5) b1 high input gnd 3.3v ci e1 low output ? ? ckstp_in d8 low input ? ? ckstp_out a6 low output ? ? clk_out d7 ? output ? ? dbb j14 low i/o ? ? dbg n1 low input ? ? dbdis h15 low input ? ? dbwo g4 low input ? ? dh[0 - 31] p14, t16, r15, t15, r13, r 12, p11, n11, r11, t12, t11, r10, p9, n9, t10, r9, t9, p8 , n8, r8, t8, n7, r7, t7, p6, n6, r6, t6, r5, n5, t5, t4 high i/o ? ? dl[0 - 31] k13, k15, k16, l16, l15, l13 , l14, m16, m15, m13, n16, n15, n13, n14, p16, p15, r16, r14, t14, n10, p13, n12, t13, p3, n3, n4, r3, t1, t2, p4, t3, r4 high i/o ? ? dp[0 - 7] m2, l3, n2, l4, r1, p2, m4, r2 high i/o ? ? drtry g16 low input ? ? gbl f1 low i/o ? ? gnd c5, c12, e3, e6, e8, e9, e11, e14, f5, f7, f10, f12, g6, g8, g9, g11, h5, h7, h10, h12, j5, j7, j10, j12, k6, k8, k9, k11, l5, l7, l10, l12, m3, m6, m8, m9, m11, m14, p5, p12 hreset a7 low input ? ? int b15 low input ? ? l1_tstclk (2) d11 high input ? ? l2_tstclk (2) d12 high input ? ? lssd_mode (2) b10 low input ? -?
9 2138e?hirel?01/05 pc755/745 atmel confidential notes: 1. ov dd supplies power to the processor bus, jtag, and all control signals and v dd supplies power to the processor core and the pll (after filtering to become avdd). these columns serve as a reference for the nominal voltage supported on a given signal as selected by the bvsel pin configuration of table 3 and the voltage supplied. for actual recommended value of v in or supply voltages see ?absolute maximum ratings (1) ? on page 14 . 2. these are test signals for factory use only and must be pulled up to ov dd for normal machine operation. 3. to allow for future i/o voltage changes, provide the option to connect bvsel independently to either ov dd (selects 3.3v) or to ognd (selects 1.8v/2.0v). 4. uses one of 15 existing no - connects in pc745?s 255 - bga package. 5. internal pull up on die. 6. internally tied to gnd in the pc745 255 - bga package to indicate to the power supply that a low - voltage processor is present. this signal is not a power supply input. mcp c13 low input ? ? nc (no - connect) b7, b8, c3, c6, c8, d5, d6, h4 , j16, a4, a5, a2, a3, b5 ? ? ? ? ovdd c7, e5, e7, e10, e12, g3, g5 , g12, g14, k3, k5, k12, k14, m5, m7, m10, m12, p7, p10 ? ? 1.8v/2.0v 3.3v pll_cfg[0 - 3] a8, b9, a9, d9 high input ? ? qack d3 low input ? ? qreq j3 low output ? ? rsrv d1 low output ? ? smi a16 low input ? ? sreset b14 low input ? ? sysclk c9 ? input ? ? ta h 1 4 l o w i n p u t ? ? tben c2 high input ? ? tbst a14 low i/o ? ? tck c11 high input ? ? tdi (5) a11 high input ? ? tdo a12 high output ? ? tea h13 low input ? ? tlbisync c4 low input ? ? tms (5) b11 high input ? ? trst (5) c10 low input ? ? ts j13 low i/o ? ? tsiz[0 - 2] a13, d10, b12 high output ? ? tt[0 - 4] b13, a15, b16, c14, c15 high i/o ? ? wt d2 low output ? ? v dd 2 f6, f8, f9, f11, g7, g10, h6, h8, h9, h11, j6, j8, j9, j11, k7, k10, l6, l8, l9, l11 ?? 2v 2v voltdet (6) f3 high output ? ? table 1. pinout listing for the pc745, 255 pbga package (continued) signal name pin number active i/o i/f voltages supported (1) 1.8v/2.0v 3.3v
10 2138e?hirel?01/05 pc755/745 atmel confidential table 2 provides the pinout listing for the pc755, 360 pbga, cbga and ci-cga + hitce table 2. pinout listing for the pc755, 360 pbga, cbga and ci-cga packages + hitce (8) signal name pin number active i/o i/f voltages supported (1) 1.8v/2.0v 3.3v a[0 - 31] a13, d2, h11, c1, b13, f2, c13, e5, d13, g7, f12, g3, g6, h2, e2, l3, g5, l4, g4, j4, h7, e1, g2 , f3, j7, m3, h3, j2, j6, k3, k2, l2 high i/o ? ? aack n3 low input ? ? abb l7 low i/o ? ? ap[0 - 3] c4, c5, c6, c7 high i/o ? ? artry l6 low i/o ? ? avdd a8 - - 2v 2v bg h1 low input ? ? br e7 low output ? ? bvsel (3)(5)(6) w1 high input gnd 3.3v ci c2 low output ? ? ckstp_in b8 low input ? ? ckstp_out d7 low output ? ? clk_out e3 ? output ? ? dbb k5 low i/o ? ? dbdis g1 low input ? ? dbg k1 low input ? ? dbwo d1 low input ? ? dh[0 - 31] w12, w11, v11, t9, w10, u9, u10, m11, m9, p8, w7, p9, w9, r10, w6, v7, v6, u8, v9, t7, u7, r7, u6, w5, u5, w4, p7, v5, v4, w3, u4, r5 high i/o ? ? dl[0 - 31] m6, p3, n4, n5, r3, m7, t2, n6, u2 , n7, p11, v13, u12, p12, t13, w13, u13, v10, w8, t11, u11, v12, v8, t1, p1, v1, u1, n1, r2, v3, u3, w2 high i/o ? ? dp[0 - 7] l1, p2, m2, v2, m1, n2, t3, r1 high i/o ? ? drtry h6 low input ? ? gbl b1 low i/o ? ? gnd d10, d14, d16, d4, d6, e12, e8, f4, f6, f10, f14, f16, g9, g11, h5, h8, h10, h12, h15, j9, j11, k4, k6, k8, k10, k12, k14, k16, l9, l11, m5, m8, m10, m12, m15, n9, n11, p4, p6, p10, p14, p16, r8, r12, t4, t6, t10, t14, t16 ??gndgnd hreset b6 low input ? ? int c11 low input ? ? l1_tstclk (2) f8 high input ? ? l2addr[0 - 16] l17, l18, l19, m19, k18, k17, k15, j19, j18, j17, j16, h18, h17, j14, j13, h19, g18 high output ? ?
11 2138e?hirel?01/05 pc755/745 atmel confidential l2avdd l13 ? ? 2v 2v l2ce p17 low output ? ? l2clkouta n15 ? output ? ? l2clkoutb l16 ? output ? ? l2data[0 - 63] u14, r13, w14, w15, v15, u15, w16, v16, w17, v17, u17, w18, v18, u18, v19, u19, t18, t17, r19, r18, r17, r15, p19, p18, p13, n14, n13, n19, n17, m17, m13, m18, h13, g19, g16, g15, g14, g13, f19, f18, f13, e19, e18, e17, e15, d19, d18, d17, c18, c17, b19, b18, b17, a18, a17, a16, b16, c16, a14, a15, c15, b14, c14, e13 high i/o ? ? l2dp[0 - 7] v14, u16, t19, n18, h14, f17, c19, b15 high i/o ? ? l2ovdd d15, e14, e16, h16, j15, l15, m16, p15, r14, r16, t 15, f15 ? ? 1.8v/2v 3.3v l2sync_in l14 ? input ? ? l2sync_out m14 ? output ? ? l2_tstclk (2) f7 high input ? ? l2vsel (1)(3)(5)(6) a19 high input gnd 3.3v l2we n16 low output ? ? l2zz g17 high output ? ? lssd_mode (2) f9 low input ? ? mcp b11 low input ? ? nc (no - connect) b3, b4, b5 , w19, k9, k11 4 , k19 4 ?? ? ? ovdd d5, d8, d12, e4, e6 , e9, e11, f5, h4, j5, l5, m4, p5, r4, r6, r9, r11, t5, t8, t12 ? ? 1.8v/2v 3.3v pll_cfg[0 - 3] a4, a5, a6, a7 high input ? ? qack b2 low input ? ? qreq j3 low output ? ? rsrv d3 low output ? ? smi a12 low input ? ? sreset e10 low input ? ? sysclk h9 ? input ? ? ta f1 low input ? ? tben a2 high input ? ? tbst a11 low i/o ? ? tck b10 high input ? ? tdi (6) b7 high input ? ? tdo d9 high output ? ? table 2. pinout listing for the pc755, 360 pbga, cbga and ci-cga packages + hitce (8) (continued) signal name pin number active i/o i/f voltages supported (1) 1.8v/2.0v 3.3v
12 2138e?hirel?01/05 pc755/745 atmel confidential notes: 1. ov dd supplies power to the processor bus, jtag, and all control signals except the l2 cache controls (l2ce, l2we, and l2zz); l2ov dd supplies power to the l2 cache interface (l2addr[0 - 16], l2data[0 - 63], l2dp[0 - 7] and l2sync - out) and the l2 control signals; and v dd supplies power to the processor core and the pll and dll (after filtering to become av dd and l2av dd respectively). these columns serve as a reference for the nominal voltage supported on a given signal as selected by the bvsel/l2vsel pin configurations of table 3 and the voltage supplied. for actual recommended value of v in or supply voltages see ?recommended operating conditions (1) ? on page 16 . 2. these are test signals for factory use only and must be pulled up to ov dd for normal machine operation. 3. to allow for future i/o voltage changes, provide the option to connect bvsel and l2vsel independently to either ov dd (selects 3.3v) or to ognd (selects 1.8v/2.0v). 4. these pins are reserved for potential future use as additional l2 address pins. 5. uses one of 9 existing no - connects in pc750?s 360 - bga package. 6. internal pull up on die. 7. internally tied to l2ov dd in the pc755 360 - bga package to indicate the power present at the l2 cache interface. this signal is not a power supply input. 8. this is different from the pc745 255-bga package. tea j1 low input ? ? tlbisync a3 low input ? ? tms (6) c8 high input ? ? trst (6) a10 low input ? ? ts k7 low i/o ? ? tsiz[0 - 2] a9, b9, c9 high output ? ? tt[0 - 4] c10, d11, b12, c12, f11 high i/o ? ? wt c3 low output ? ? vdd g8, g10, g12, j8, j10, j12, l8, l10, l12, n8, n10, n12 ? ? 2v 2v voltdet (7) k13 high output ? ? table 2. pinout listing for the pc755, 360 pbga, cbga and ci-cga packages + hitce (8) (continued) signal name pin number active i/o i/f voltages supported (1) 1.8v/2.0v 3.3v
13 2138e?hirel?01/05 pc755/745 atmel confidential signal description figure 4. pc755 microprocessor signal groups br bg abb ts tt[0-4] ap[0-3] tbst ts1z[0-2] gbl wt ci aack artr y dbg dbwo dbb l2addr [16-0] l2data [0-63] l2dp [0-7] l2clk-out [a-b] l2we a[0-31] l2sync_out l2sync_in int smi mcp hreset ckstp_in ckstp_out sysclk, pll_cfg [0-3] 4 17 64 8 factory test jt ag:cop address arbitration address start address bus transfer attribute address termination data arbitra tion l2 cache l2 vsel address/ dat a l2 cache clock/control interrupts reset clock control test interface 1 1 2 1 1 1 1 1 1 5 3 1 1 1 1 1 32 4 5 3 1 1 1 1 1 1 d[0-63] data transfer d[p0-7] dbdis ta data termina tion drtr y tea pc755b l2av dd l2v dd sreset 1 1 rsr v tben tlbisync qreq qack processor status control clk_out 1 1 1 1 1 1 1 1 v dd av dd l2ce l2zz not supported in the pc745b 1 1 8 1 1 1 11 64 gnd ov dd voltdet
14 2138e?hirel?01/05 pc755/745 atmel confidential detailed specifications this specification describes the specific requirements for the microprocessor pc755, in compli- ance with atmel grenoble standard screening. applicable documents 1) mil-std-883: test methods and procedures for electronics. 2) mil-prf-38535 appendix a: general specifications for microcircuits. the microcircuits are in accordance with the applicable documents and as specified herein. design and construction terminal connections depending on the package, the terminal connections is shown in table 1 , table 2 and figure 4 . notes: 1. functional and tested operating conditions are given in ?recommended operating conditions (1) ? on page 16 . absolute max- imum ratings are stress ratings only, and functional operation at the maximums is not guar anteed. stresses beyond those listed may affect device reliability or cause permanent damage to the device. 2. caution: v in must not exceed ov dd or l2ov dd by more than 0.3v at any time including during power-on reset. 3. caution: l2ov dd /ov dd must not exceed v dd /av dd /l2av dd by more than 1.6v during normal operation. during power-on reset and power-down sequences, l2ov dd /ov dd may exceed v dd /av dd /l2av dd by up to 3.3v for up to 20 ms, or by 2.5v for up to 40 ms. excursions beyond 3.3v or 40 ms are not supported. 4. caution: v dd /av dd /l2av dd must not exceed l2ov dd /ov dd by more than 0.4v during normal operation. during power-on reset and power-down sequences, v dd /av dd /l2av dd may exceed l2ov dd /ov dd by up to 1.0v for up to 20 ms, or by 0.7v for up to 40 ms. excursions beyond 1.0v or 40 ms are not supported. 5. this is a dc specifications only. v in may overshoot/undershoot to a voltage and for a maximum duration as shown in figure 5 . absolute maximum ratings (1) characteristic symbol maximum value unit core supply voltage (4) v dd -0.3 to 2.5 v pll supply voltage (4) av dd -0.3 to 2.5 v l2 dll supply voltage (4) l2av dd -0.3 to 2.5 v processor bus supply voltage (3) ov dd -0.3 to 3.6 v l2 bus supply voltage (3) l2ov dd -0.3 to 3.6 v input voltage processor bus (2)(5) v in -0.3 to ov dd + 0.3v v l2 bus (2)(5) v in -0.3 to l2ov dd + 0.3v v jtag signals v in -0.3 to 3.6 v storage temperature range t stg -65 to 150 c rework temperature t rwk 220 c
15 2138e?hirel?01/05 pc755/745 atmel confidential figure 5 shows the allowable undershoot and overshoot voltage on the pc755 and pc745. figure 5. overshoot/undershoot voltage the pc755 provides several i/o vo ltages to support bo th compatibility with existing systems and migration to future systems. the pc755 core voltage must always be provided at nominal 2.0v (see ?recommended operating conditions (1) ? on page 16 for actual recommended core volt- age). voltage to the l2 i/os and processor interface i/os are provided through separate sets of supply pins and may be provided at the voltages shown in table 3 . the input voltage threshold for each bus is selected by sampling the stat e of the voltage select pins bvsel and l2vsel during operation. these signals must remain stable during part operation and cannot change. the output voltage will swing from gnd to the ma ximum voltage applied to the ov dd or l2ov dd power pins. table 3 describes the input threshold voltage setting. notes: 1. caution: the input threshold selection must agree with the ov dd /l2ov dd voltages supplied. 2. the input threshold settings above are different for all revisi ons prior to rev. 2.8 (rev. e). for more information, contact your local atmel sales office. (l2) ov dd +20% (l2) ov dd +5% (l2) ov dd gnd - 1.0v gnd - 0.3v gnd v ih not to exceed 10% of t sysclk v il table 3. input threshold voltage setting part revision bvsel sign al processor bus interfac e voltage l2vsel signal l2 bus interface voltage e 0 not available 0 not available 1 2.5v/3.3v 1 2.5v/3.3v
16 2138e?hirel?01/05 pc755/745 atmel confidential notes: 1. these are the recommended and tested operating condition s. proper device operation outside of these conditions is not guaranteed. 2. revisions prior to rev. 2.8 (rev. e) offered different i/o voltage support. 3. 2.0v nominal. 4. 2.5v nominal. 5. 3.3v nominal. recommended operating conditions (1) recommended value unit 300 mhz, 350 mhz 400 mhz characteristic symbol min max min max core supply voltage (3) v dd 1.80 2.10 1.90 2.10 v pll supply voltage (3) av dd 1.80 2.10 1.90 2.10 v l2 dll supply voltage (3) l2av dd 1.80 2.10 1.90 2.10 v processor bus supply voltage (2)(4)(5) bvsel = 1 ov dd 2.375 2.625 2.375 2.625 v 3.135 3.465 3.135 3.465 v l2 bus supply voltage (2)(4)(5) l2vsel = 1 l2ov dd 2.375 2.625 2.375 2.625 v 3.135 3.465 3.135 3.465 v input voltage processor bus v in gnd ov dd gnd ov dd v l2 bus v in gnd l2ov dd gnd l2ov dd v jtag signals v in gnd ov dd gnd ov dd v die-junction temperature military temperature range t j -55 125 -55 125 c industrial temperature t j -40 110 -40 110 c
17 2138e?hirel?01/05 pc755/745 atmel confidential thermal characteristics package characteristics table 4 provides the package thermal characteristics for the pc755. notes: 1. junction temperature is a function of on-chip power diss ipation, package thermal resistance, mounting site (board) temp era- ture, ambient temperature, air flow, power dissipation of ot her components on the board, and board thermal resistance. 2. per semi g38-87 and jedec jesd51-2 wit h the single layer board horizontal. 3. per jedec jesd51-6 with the board horizontal. 4. thermal resistance between the die and the printed circuit board per jedec jesd51-8. boar d temperature is measured on the top surface of the board near the package. 5. thermal resistance between the die and the case top surf ace as measured by the cold plate method (mil spec-883 method 1012.1) with the calculated case temperature. the actual value of r y jc for the part is less than 0.1 c/w. note: r efer to section ?thermal management information? page 19 for more details about thermal management. package thermal characteristics for hitce table 5 provides the package thermal characteristics for the pc755, hitce. notes: 1. simulation, no convection air flow. 2. per jedec jesd51-6 with the board horizontal. the board designer can choose between several types of heat sinks to place on the pc755. there are several commercially-available heat sinks for the pc755 provided by the following vendors. table 4. package thermal characteristics characteristic symbol value unit pc755 cbga pc755 pbga pc745 pbga junction-to-ambient thermal resistance, natural convection (1)(2) r ja 24 31 34 c/w junction-to-ambient thermal resistance, natural convection, four-layer (2s2p) board (1)(3) r jma 17 25 26 c/w junction-to-ambient thermal resistance, 200 ft./min. airflow, single-layer (1s) board (1)(3) r jma 18 25 27 c/w junction-to-ambient thermal resistance, 200 ft./min. airflow, four-layer (2s2p) board (1)(3) r jma 14 21 22 c/w junction-to-board thermal resistance (4) r jb 81717 c/w junction-to-case thermal resistance (5) r jc < 0.1 < 0.1 < 0.1 c/w table 5. package thermal characte ristics for hitce package characteristic symbol value unit pc755 hitce junction-to-bottom of balls (1) r j 6.8 c/w junction-to-ambient thermal resistance, natural convection, four-layer (2s2p) board (1)(2) r jma 20.7 c/w junction to board thermal resistance r jb 11.0 c/w table 6. package thermal charac teristics for ci-cga characteristic symbol value unit pc755 ci-cga junction to board thermal resistance r jb 8.42 c/w
18 2138e?hirel?01/05 pc755/745 atmel confidential for the exposed-die packaging technology, shown in ?recommended operating conditions (1) ? on page 16 , the intrinsic conduction thermal resistance paths are as follows: the die junction-to-case (or top-of-die for exposed silicon) thermal resistance the die junction-to-ball thermal resistance figure 6 depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit board. heat generated on t he active side of the chip is conducted th rough the silicon, then through the heat sink attach material (or thermal interface material), and finally to the heat sink where it is removed by forced-air convection. since the silicon ther mal resistance is quite sm all, for a first-order anal ysis, the temp erature drop in the silicon may be neglected. thus, the heat sink attach ma terial and the heat sink conduc- tion/convective thermal resistances are the dominant terms. figure 6. c4 package with head sink mounted to a printed-circuit board note the internal versus external package resistance. external resistance external resistance internal resistance radiation convection radiation convection heat sink printed circuit board thermal interface material package/leads die junction die/package
19 2138e?hirel?01/05 pc755/745 atmel confidential thermal management assistance the pc755 incorporates a thermal management assist unit (tau) composed of a thermal sen- sor, digital-to-analog converter, comparator , control logic, and dedicated special-purpose registers (sprs). specifications for the thermal sensor portion of the tau are found in table 7 . more information on the use of this feature is given in the freescale pc755 risc microproces- sor user?s manual. notes: 1. the temperature is the junction temperature of the die. the thermal assist unit?s raw output does not indicate an absolute temperature, but mu st be interpreted by software to derive the absolute junction temperature. for information about the use and calibration of the tau, see freescale application note an1800/d, ?programming the thermal assist unit in the pc750 microprocessor?. 2. the comparator settling time value must be converted into the number of cpu clocks that need to be written into the thrm3 spr. 3. guaranteed by design and characterization. thermal management information this section provides thermal management info rmation for the ceramic ball grid array (bga) package for air-cooled applications. proper thermal control design is primarily dependent upon the system-level design-the heat sink, airflow and thermal interface material. to reduce the die- junction temperature, heat sinks may be attach ed to the package by several methods-adhesive, spring clip to holes in the printed-circuit board or package, and mounting clip and screw assem- bly; see figure 7 . this spring force should not exceed 5.5 pounds of force. figure 7. package exploded cross-sectional view with several heat sink options ultimately, the final selection of an appropriate heat sink depends on many factors, such as ther- mal performance at a given air velocity, spatial volume, mass, attachment method, assembly, and cost. table 7. thermal sensor specifications at recommended operating conditions (see ?recommended operating conditions (1) ? on page 16 ) characteristic min max unit temperature range (1) 0 127 c comparator settling time (2)(3) 20 ? s resolution (3) 4? c accuracy (3) -12 +12 c adhesive or thermal interface material heat sink heat sink clip printed circuit board option bga package
20 2138e?hirel?01/05 pc755/745 atmel confidential adhesives and thermal interface materials figure 8. thermal performance of select thermal interface material a thermal interface material is recommended at the package lid-to-heat sink interface to mini- mize the thermal contact resistance. for those applications where the heat sink is attached by spring clip mechanism, figure 8 shows the thermal performance of three thin-sheet thermal- interface materials (silicone, graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function of contact pressure. as shown, the performance of these thermal interface materials improves with increasing contact pr essure. the use of thermal grease significantly reduces the interface thermal resistance. that is, the bare joint results in a thermal resistance approximately 7 times greater than the thermal grease joint. heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see figure 7 ). this spring force should not exceed 5.5 pounds of force. therefore, the synthetic grease offers the best thermal performance, considering the low interface pressure. the board designer can choose between several ty pes of thermal interface. heat sink adhesive materials should be selected based upon high conductivity, yet adequate mechanical strength to meet equipment shock/vibration requirements. heat sink selection example for preliminary heat sink sizing, the die-junction temperature can be expressed as follows: t j = t a + t r + ( jc + int + sa ) * p d where : t j is the die-junction temperature t a is the inlet cabinet ambient temperature t r is the air temperature rise within the computer cabinet jc is the junction-to-case thermal resistance int is the adhesive or interface material thermal resistance 0 0.5 1 1.5 2 silicone sheet (0.006 inch) bare joint floroether oil sheet (0.007 inch) graphite/oil sheet (0.005 inch) synthetic grease contact pressure (psi) specific thermal resistance (kin2/w) 0 1020304050607080
21 2138e?hirel?01/05 pc755/745 atmel confidential sa is the heat sink base-to-ambient thermal resistance p d is the power dissipated by the device during operation the die-junction temperatures (t j ) should be maintained less than the value specified in table 5. the temperature of the air cooling the component greatly depends upon the ambient inlet air temperature and the air temperature rise within the electronic cabinet. an elec- tronic cabinet inlet-air temperature (t a ) may range from 30 to 40 c. the air temperature rise within a cabinet (t r ) may be in the range of 5 to 10 c. the thermal resistance of the thermal interface material ( int ) is typically about 1 c/w. assuming a t a of 30 c, a t r of 5 o c, a cbga package jc = 0.03, and a power consumption (p d ) of 5.0 watts, the following expression for t j is obtained: die-junction temperature: t j = 30 c + 5 c + (0.03 c/w + 1.0 c/w + sa ) * 5.0 w for a thermalloy heat sink #2328b, the heat sink-to-ambient thermal resistance ( sa ) versus air- flow velocity is shown in figure 9 . figure 9. thermalloy #2328b heat sink-to-ambient thermal resistance versus airflow velocity assuming an air velocity of 0. 5 m/s, we have an effective r sa of 7 c/w, thus t j = 30 c + 5 c+ (0.03 c/w +1.0 c/w + 7 c/w) * 5.0 w, resulting in a die-junction temperature of approximately 81 c which is well within the maximum operating temperature of the component. other heat sinks offered by chip coolers, ierc, thermalloy, wakefield engineering, and aavid engineering offer different heat sink-to-ambient thermal resistances, and may or may not need air flow. 1 3 5 7 8 0 0.5 1 1.5 2 2.5 3 3.5 thermalloy #2328b pinfin heat sink approach air velocity (m/s) (25 x28 x 15 mm) 2 4 6 heat sink thermal resistance c/w)
22 2138e?hirel?01/05 pc755/745 atmel confidential though the die junction-to-ambient and the heat sink-to-ambient thermal resistances are a com- mon figure-of-merit used for comparing the thermal performance of various microelectronic packaging technologies, one should exercise cautio n when only using this metric in determining thermal management because no single parameter can adequately describe three-dimensional heat flow. the final die-junction operating temper ature, is not only a function of the component- level thermal resistance, but the system-level de sign and its operating conditions. in addition to the component?s power consumption, a number of factors affect the final operating die-junction temperature ? airflow, board population (local heat flux of adjacent components), heat sink effi- ciency, heat sink attach, heat sink placemen t, next-level interconnect technology, system air temperature rise, altitude, etc. due to the complexity and the many variations of system-level boundary conditions for today?s microelectronic equipment, the combined effects of the heat transfer mechanisms (radiation, convection and conduction) may vary widely. fo r these reasons, we recommend using conju- gate heat transfer models for the board, as well as, system-level designs. to expedite system- level thermal analysis, several ?compact? thermal-package models are available within flo- therm ? . these are available upon request. power consideration power management the pc755 provides four power modes, selectable by setting the appropriate control bits in the msr and hido registers. the four power modes are as follows: full-power: this is the default power state of the pc755. the pc755 is fully powered and the internal functional units operate at the full processor clock speed. if the dynamic power management mode is en abled, functional units that are id le will automatically enter a low- power state without affecting performance, software execution, or external hardware. doze: all the functional units of the pc755 are disabled except for the time base/decrementer registers and the bus snooping logic. when the processor is in doze mode, an external asynchronous interrupt, a system management interrupt, a decrementer exception, a hard or soft reset, or machine check brings the pc755 into the full-power state. the pc755 in doze mode maintains the pll in a fully powered state and locked to the system external clock input (sysclk) so a transition to the full-power state takes only a few processor clock cycles. nap: the nap mode further reduces power consumption by disabling bus snooping, leaving only the time base register and the pll in a powered state. the pc755 returns to the full- power state upon receipt of an external a synchronous interrupt, a system management interrupt, a decrementer exception, a hard or soft reset, or a machine check input (mcp). a return to full-power state from a nap state takes only a few processor clock cycles. when the processor is in nap mode, if qack is negated, the processor is put in doze mode to support snooping. sleep: sleep mode minimizes power consumption by disabling all internal functional units, after which external system logic may disable the ppl and susclk. returning the pc755 to the full-power state requ ires the enabling of the pp l and sysclk, followed by the assertion of an external asynchronous interrupt, a system management interrupt, a hard or soft reset, or a machine check input (mcp) signal after the time required to relock the ppl.
23 2138e?hirel?01/05 pc755/745 atmel confidential power dissipation notes: 1. these values apply for all valid processor bus and l2 bus ratios. the values do not include i/o supply power (ov dd and l2ov dd ) or pll/dll supply power (av dd and l2av dd ). ov dd and l2ov dd power is system dependent, but is typically < 10% of v dd power. worst case power consumption for av dd = 15 mw and l2av dd = 15 mw. 2. maximum power is measured at nominal v dd (see ?recommended operating conditions (1) ? on page 16 ) while running an entirely cache-resident, c ontrived sequence of instructions which keep the execution units maximally busy. 3. typical power is an average value measured at the nominal recommended v dd (see ?recommended operating conditions (1) ? on page 16 ) and 65c in a system while run- ning a typical code sequence. 4. not 100% tested. characterized and periodically sampled. table 8. power consumption for pc755 processor (cpu) frequency unit 300 mhz 350 mhz 400 mhz full-power mode typical (1)(3)(4) 3.1 3.6 5.4 w maximum (1)(2) 4.5 5.3 8 w doze mode maximum (1)(2)(4) 1.8 2 2.3 w nap mode maximum (1)(2)(4) 111w sleep mode maximum (1)(2)(4) 550 550 550 mw sleep mode-pll and dll disabled maximum (1)(2) 510 510 510 mw
24 2138e?hirel?01/05 pc755/745 atmel confidential electrical characteristics static characteristics notes: 1. nominal voltages; see ?recommended operating conditions (1) ? on page 16 . 2. for processor bus signals, the reference is ov dd while l2ov dd is the reference for the l2 bus signals. 3. excludes test signals (lssd_mode, l1_tstclk, l2_tstclk) and ieee 1 149.1 boundary scan (jtag) signals. 4. capacitance is periodically sampled rather than 100% tested. 5. the leakage is measured for nominal ov dd and v dd , or both ov dd and v dd must vary in the same direction (for example, both ov dd and v dd vary by either +5% or - 5%). table 9. dc electrical specifications at reco mmended operating conditions (see ?recommended operating condi- tions (1) ? on page 16 ) characteristic nominal bus voltage (1) symbol min max unit input high voltage (all inputs except syslck) (2)(3) 2.5 v ih 1.6 (l2)ov dd + 0.3 v 3.3 v ih 2(l2)ov dd + 0.3 v input low voltage (all inputs except syslck) (2) 2.5 v il -0.3 0.6 v 3.3 v il -0.3 0.8 v sysclk input high voltage 2.5 kv ih 1.8 ov dd + 0.3 v 3.3 kv ih 2.4 ov dd + 0.3 v sysclk input low voltage 2.5 kv il -0.3 0.4 v 3.3 kv il -0.3 0.4 v input leakage current, (2)(3) v in = l2ov dd /ov dd i in ?10a hi-z (off-state) leakage current, (2)(3)(5) v in = l2ov dd /ov dd i tsi ?10a output high voltage, i oh = - 6 ma 2.5 v oh 1.7 ? v 3.3 v oh 2.4 ? v output low voltage, i ol = 6 ma 2.5 v ol ?0.45v 3.3 v ol ?0.4v capacitance, v in = 0v, f = 1 mhz (3)(4) c in ?5pf
25 2138e?hirel?01/05 pc755/745 atmel confidential dynamic characteristics after fabrication, parts are sorted by maximum processor core frequency as shown in ?clock ac specifications? on page 25 and tested for conformance to the ac specifications for that fre- quency. these specifications are for 275, 300, 333 mhz processor core frequencies. the processor core frequency is determined by the bus (sysclk) frequency and the settings of the pll_cfg[0-3] signals. parts are sold by maximum processor core frequency. clock ac specifications table 10 provides the clock ac timing specifications as defined in ?absolute maximum rat- ings (1) ? on page 14 . notes: 1. caution: the sysclk frequency and pll_cfg[0 - 3] settings must be chosen such t hat the resulting sysclk (bus) fre- quency, cpu (core) frequency, and pll (vco) frequency do not exceed their respective maximum or minimum operating frequencies. refer to the pll_cfg[0 - 3] signal description in table 16 ,? for valid pll_cfg[0 - 3] settings 2. rise and fall times measurements are now specified in terms of sl ew rates, rather than time to account for selectable i/o bus interface levels. the minimum slew rate of 1v/ns is equivalent to a 2ns maximum rise/fall time measured at 0.4v and 2.4v or a rise/fall time of 1ns measured at 0.4v to 1.4v. 3. timing is guaranteed by design and characterization. 4. this represents total input jitter ? short term and long term combined and is guaranteed by design. 5. relock timing is guaranteed by design and characterization. pll - relock time is the maximum am ount of time required for pll lock after a stable v dd and sysclk are reached during the power - on reset sequence. this specification also applies when the pll has been disabled and subsequently re - enabled during sleep mode . also note that hreset must be held asserted for a minimum of 255 bus clocks after the pll - relock time during the power - on reset sequence. figure 10 provides the sysclk input timing diagram. figure 10. sysclk input timing diagram table 10. clock ac timing specifications at recommended operating conditions (see ?recommended operating condi- tions (1) ? on page 16 ) characteristic symbol maximum processor core frequency unit 300 mhz 350 mhz 400 mhz min max min max min max processor frequency (1) f core 200 300 200 350 200 400 mhz vco frequency (1) f vco 400 600 400 700 400 800 mhz sysclk frequency (1) f sysclk 25 100 25 100 25 100 mhz sysclk cycle time t sysclk 10 40 10 40 10 40 ns sysclk rise and fall time (2) t kr & t kf ?2?2?2 ns t kr & t kf ?1.4?1.4?1.4 ns sysclk duty cycle measured at ov dd /2 (3) t khkl /t sysclk 40 60 40 60 40 60 % sysclk jitter (3)(4) ? 150 ? 150 ? 150 ps internal pll relock time (3)(5) ?100?100?100 s s ysclk vm vm vm kv ih kv il vm = midpoint voltage (ov dd /2 ) t sysclk t kr t kf t khkl
26 2138e?hirel?01/05 pc755/745 atmel confidential processor bus ac specifications table 11 provides the processor bus ac timing specifications for the pc755 as defined in figure 11 and figure 13 . timing specifications for the l2 bus are provided in ?l2 clock ac specifica- tions? on page 28 . notes: 1. all input specifications are measur ed from the midpoint of the signal in question to the midpoint of the rising edge of the input sysclk. all output specifications are measured from the midpoi nt of the rising edge of sysclk to the midpoint of the sig- nal in question. all output timings assume a purely resistive 50 ? load (see figure 11 ). input and output timings are measured at the pin; time - of - flight delays must be added for trace lengths, vias, and connectors in the system. 2. the symbology used for timing specifications herein follows the pattern of t (signal)(state)(reference)(state) for inputs and t (reference)(state)(signal)(state) for outputs. for example, t ivkh symbolizes the time input signals (i ) reach the valid state (v) relative to the sysclk reference (k) going to the high (h) state or input setup time. and t khov symbolizes the time from sysclk(k) going highs) until outputs (o) are valid (v) or output valid time. input hold time can be read as the time that the input signa l (i) went invalid (x) with respect to the rising clock edge (kh) - note the position of the reference and its state for inputs ? and output hold time can be read as the time from the rising edg e (kh) until the output went invalid (ox). for additional explana- tion of ac timing specifications in freescale powerpc microp rocessors, see the application note ?understanding ac timing specifications for powerpc microprocessors.? 3. the setup and hold time is with respect to the rising edge of hreset (see figure 11 ). 4. this specification is for configuration mode select only. also note that the hreset must be held asserted for a minimum of 255 bus clocks after the pll re - lock time during the power - on reset sequence. 5. t sysclk is the period of the external clock (sysclk) in nanoseconds (ns). the numbers given in the table must be multiplied by the period of sysclk to compute the actual time durati on (in nanoseconds) of t he parameter in question. 6. mode select signals are bvsel, l2vsel, pll_cfg[0 - 3] 7. guaranteed by design and characterization. 8. bus mode select pins must remain stable during operation. changing the logic states of bvsel or l2vsel during operation will cause the bus mode voltage selection to change. changing the logic states of the pll_cfg pins during operation will cause the pll division ratio selection to change. both of th ese conditions are considered ou tside the specification and are not supported. once hreset is negated the states of the bus mode selection pins must remain stable. figure 11 provides the mode select input timing diagram for the pc755. figure 11. mode input timing diagram table 11. processor bus mode selection ac timing specifications (1) at v dd = a v dd = 2.0v 100 mv; -55 t j +125 c, ov dd = 3.3v 165 mv and ov dd = 1.8v 100 mv and ov dd = 2.0v 100 mv parameter symbols (2) all speed grades unit min max mode select input setup to hreset (3)(4)(5)(6)(7) t mvrh 8?t sysclk hreset to mode select input hold (3)(4)(6)(7)(8) t mxrh 0?ns hreset mode signals vm = midpoint voltage (ov dd /2) vm t mvrh t mxrh
27 2138e?hirel?01/05 pc755/745 atmel confidential figure 12 provides the ac test load for the pc755. figure 12. ac test load notes: 1. revisions prior to rev 2.8 (rev e) were limited in perfo rmance and did not conform to this specification. contact your local freescale sales office for more information. 2. guaranteed by design and characterization. 3. t sysclk is the period of the external clock (sysclk) in nanoseconds (ns) . the numbers given in th e table must be multiplied by the period of sysclk to comp ute the actual time du ration (in ns) of the parameter in question. 4. per the 60x bus protocol, ts , abb and dbb are driven only by the currently active bus master. they are asserted low then precharged high before returning to high-z as shown in figure 6 . the nominal precharge width for ts , abb or dbb is 0.5 x t sysclk , i.e. less than the minimum t sysclk period, to ensure that ano ther master asserting ts , abb , or dbb on the following clock will not contend with the precharge. output valid and output hold timing is tested for the signal asserted. output valid time is tested for precharge.the high-z behavior is guaranteed by design. 5. per the 60x bus protocol, artry can be driven by multiple bus masters through the clock period immediately following aack . bus contention is not an issue since any master asserting artry will be driving it low. any master asserting it low in the first clock following aack will then go to high-z for one clock before precharging it high during the second cycle after th e assertion of aack . the nominal precharge width for artry is 1.0 t sysclk ; i.e., it should be high-z as shown in figure 6 before the first opportunity for another master to assert artry . output valid and output hold timing is tested for the signal asserted. output valid time is tested for precharge. t he high-z and precharge behavior is guaranteed by design. ov dd /2 output z 0 = 50 ? r l = 50 ? table 12. processor bus ac timing specifications (1) at recommended operating conditions parameter symbols all speed grades unit min max setup times: all inputs t ivkh 2.5 ? ns input hold times: tlbisync , mcp , smi t ixkh 0.6 ? ns input hold times: all inputs, except tlbisync , mcp , smi t ixkh 0.2 ? ns valid times: all outputs t khov ?4.1ns output hold times: all outputs t khox 1?ns sysclk to output enable (2) t khoe 0.5 ? ns sysclk to output high impedance (all except abb , artry , dbb ) (2) t khoz ?6ns sysclk to abb , dbb high impedance after precharge (2)(3)(4) t khabpz ?1t sysclk maximum delay to artry precharge (2)(3)(5) t kharp ?1t sysclk sysclk to artry high impedance after precharge (2)(3)(5) t kharpz ?2t sysclk
28 2138e?hirel?01/05 pc755/745 atmel confidential figure 13 provides the input/output timing diagram for the pc755. figure 13. input/output timing diagram l2 clock ac specifications the l2clk frequency is programmed by the l2 configuration register (l2cr[4:6]) core-to-l2 divisor ratio. see table 13 for example core and l2 frequencies at various divisors. table 13 provides the potential range of l2clk output ac timing specifications as defined in figure 14 . the minimum l2clk frequency of table 13 is specified by the maximum delay of the internal dll. the variable-tap dll introduces up to a full clock period delay in the l2clkouta, l2clkoutb, and l2sync_out signals so that the returning l2sync_in signal is phase aligned with the next core clock (divided by the l2 divisor ratio). do not choose a core-to-l2 divi- sor which results in an l2 frequency below this minimum, or the l2clkout signals provided for sram clocking will not be pha se aligned with the pc755 core clock at the srams. the maximum l2clk frequency shown in table 13 is the core frequency divided by one. very few l2 sram designs will be able to operate in this mode. mo st designs will se lect a greater core-to-l2 divisor to provide a longer l2clk period for read and write access to the l2 srams. the maximum l2clk frequency for any application of the pc755 will be a function of the ac timings of the pc755, the ac timings for the sram, bus loading, and printed circuit board trace length. sysclk all inputs vm vm = midpoint voltage (ov dd /2 or v in /2 ) all output s vm (except ts , abb, artr y, d b b ) ts ,abb,db b artr y vm t ivkh t ixkh t khoe t khov t khox t khabpz t khov t khox t khoz t kharpz t khov t khox t kharp t khov t khoz
29 2138e?hirel?01/05 pc755/745 atmel confidential freescale is similarly limited by system constraints and cannot perform tests of the l2 interface on a socketed part on a functional tester at the maximum frequencies of table 13 . therefore functional operation and ac timing information are tested at core-to-l2 divisors of 2 or greater. functionality of core-to-l2 divisors of 1 or 1.5 is verified at less than maximum rated frequencies. l2 input and output signals are latched or enabled respectively by the internal l2clk (which is sysclk multiplied up to the core frequency and divided down to the l2cl k frequency). in other words, the ac timings of table 14 and table 15 are entirely independent of l2sync_in. in a closed loop system, where l2sy nc_in is driven through the board trace by l2sync_out, l2sync_in only controls the output phase of l2clkouta and l2clkoutb which are used to latch or enable data at the srams. however, since in a closed loop system l2sync_in is held in phase alignment with the internal l2clk, the signals of table 14 and table 15 are referenced to this signal rather than the not-externally-visible internal l2clk. during manufacturing test, these times are actually measured relative to sysclk. the l2sync_out signal is intended to be routed halfway out to the srams and then returned to the l2sync_in input of the pc755 to synchronize l2clkout at the sram with the proces- sor?s internal clock. l2clkout at the sram c an be offset forward or backward in time by shortening or lengthening the routing of l2 sync_out to l2sync_in. see freescale applica- tion note an179/d ?powerpc ? backside l2 timing analysis for the pcb design engineer.? the l2clkouta and l2clkoutb signals should not have more than two loads. notes: 1. l2clk outputs are l2clk_outa, l2clk_outb, l2clk_out and l2sync_out pins. the l2clk frequency to core fre- quency settings must be chosen so that the resulting l2cl k frequency and core frequency do not exceed their respective maximum or minimum operating frequencies. the maximum l2lck frequency will be system dependent. l2clk_outa and l2clk_outb must have equal loading. 2. the nominal duty cycle of the l2clk is 50% measur ed at midpoint voltage. 3. the dll re - lock time is specified in terms of l2clks. the number in the table must be multiplied by the period of l2clk to compute the actual time duration in nanoseconds. re - lock timing is guaranteed by design and characterization. 4. the l2cr[l2sl] bit should be set for l2clk frequencies less th an 110 mhz. this adds more delay to each tap of the dll. 5. allowable skew between l2sync_out and l2sync_in. 6. this output jitter number re presents the maximum delay of one tap forward or one tap back from the current dll tap as the phase comparator seeks to minimize the phase difference between l2sync_in and the internal l2clk. this number must be comprehended in the l2 timing analysis. the input jitter on sysclk affects l2clkout and the l2 address/data/control signals equally and therefore is already comprehended in the ac timing and does not have to be considered in the l2 timing analysis. 7. guaranteed by design. table 13. l2clk output ac timing specification. at v dd = a v dd = 2.0v 100 mv; -55 t j +125 c, ov dd = 3.3v 165 mv and ov dd = 1.8v 100 mv and ov dd = 2.0v 100 mv parameter symbols all speed grades unit min max l2clk frequency (1)(4) f l2clk 80 450 mhz l2clk cycle time t l2clk 2.5 12.5 ns l2clk duty cycle (2)(7) t chcl /t l2clk 45 55 % internal dll - relock time (3)(7) ? 640 ? l2clk dll capture window (5)(7) ? 0 10 ns l2clkout output - to - output skew (6)(7) t l2cskw ?50 ps l2clkout output jitter (6)(7) ? ? 150 ps
30 2138e?hirel?01/05 pc755/745 atmel confidential the l2clk_out timing diagram is shown in figure 14 . figure 14. l2clk_out output timing diagram l2 bus input ac specifications table 14 provides the l2 bus interface ac timing specifications for the pc755 as defined in fig- ure 15 and figure 16 for the loading conditions described in figure 17 . vm = midpoint voltage (l2ovdd/2) l2clk_outa l2clk_outb l2 differential clock mode l2 single-ended clock mode l2sync_out l2clk_out a vm t l2cr t l2cf vm vm vm l2clk_out b vm vm vm vm vm l2sync_ out vm vm vm vm vm vm vm vm t l2cskw t l2clk t l2clk t chcl t chcl table 14. l2 bus interface ac timing specifications at recommended operating conditions parameter symbol all speed grades unit min max l2sync_in rise and fall time (1) t l2cr & t l2cf ?1.0ns setup times: data and parity (2) t dvl2ch 1.2 - ns input hold times: data and parity (2) t dxl2ch 0-ns valid times: (3)(4) all outputs when l2cr[14-15] = 00 all outputs when l2cr[14-15] = 01 all outputs when l2cr[14-15] = 10 all outputs when l2cr[14-15] = 11 t l2chov - - - - 3.1 3.2 3.3 3.7 ns output hold times: (3) all outputs when l2cr[14-15] = 00 all outputs when l2cr[14-15] = 01 all outputs when l2cr[14-15] = 10 all outputs when l2cr[14-15] = 11 t l2chox 0.5 0.7 0.9 1.1 - - - - ns l2sync_in to high impedance: (3)(5) all outputs when l2cr[14-15] = 00 all outputs when l2cr[14-15] = 01 all outputs when l2cr[14-15] = 10 all outputs when l2cr[14-15] = 11 t l2choz - - - - 2.4 2.6 2.8 3.0 ns
31 2138e?hirel?01/05 pc755/745 atmel confidential notes: 1. rise and fall times for the l2sync_in input are measured from 20% to 80% of l2ov dd . 2. all input specifications are measured from the midpoint of the signal in question to the midpoint voltage of the rising edge of the input l2sync_in (see figure 8 ). input timings are measured at the pins. 3. all output specifications are me asured from the midpoint voltage of the rising edge of l2sync_in to the midpoint of the sig- nal in question. the output timings are measured at t he pins. all output timings assume a purely resistive 50 ? load (see figure 10 ). 4. the outputs are valid for both single -ended and differential l2clk modes. for pipelined registered synchronous bur- strams, l2cr[14 - 15] = 01 or 10 is recommended. for pipelined late write synchronous burstrams, l2cr[14 - 15] = 11 is recommended. 5. guaranteed by design and characterization. 6. revisions prior to rev 2.8 (rev e) were limited in performanc e.and did not conform to this specification. contact your local atmel sales office fo r more information. figure 15 shows the l2 bus input timing diagrams for the pc755. figure 15. l2 bus input timing diagrams figure 16 shows the l2 bus output timing diagrams for the pc755. figure 16. l2 bus output timing diagrams figure 17 provides the ac test load for l2 interface of the pc755. figure 17. ac test load for the l2 interface l2sync_ in l2 data and dat a vm vm = midpoint voltage (l2ov dd /2) t dvl2ch t dxl2ch t l2cr t l2cf parity inputs l2sync_in all outputs vm vm = midpoint voltage (l2ov dd /2) vm l2data bus t l2chox t l2choz t l2chov output l2ovdd/2 r l = 50 ? z 0 = 50 ?
32 2138e?hirel?01/05 pc755/745 atmel confidential ieee 1149.1 ac timing specifications table 15 provides the ieee 1149.1 (jtag) ac timing specific ations as defined in figure 18 , fig- ure 19 , figure 20 , and figure 21 . notes: 1. all outputs are measured from the mi dpoint voltage of the falling/rising edge of tclk to the midpoint of the signal in ques- tion. the output timings are measured at the pins . all output timings assume a purely resistive 50 ? load (see figure 18 ). time - of - flight delays must be added for trace lengths, vias, and connectors in the system. 2. trst is an asynchronous level sensitive signal. the setup time is for test purposes only. 3. non - jtag signal input timing with respect to tck. 4. non - jtag signal output timing with respect to tck. 5. guaranteed by design and characterization. figure 18 provides the ac test load for tdo and the boundary-scan outputs of the pc755. figure 18. alternate ac test load for the jtag interface table 15. jtag ac timing specificat ions (independ ent of sysclk) (1) parameter symbol min max unit tck frequency of operation f tclk 016mhz tck cycle time f tclk 62.5 - ns tck clock pulse width measured at 1.4v t jhjl 31 - ns tck rise and fall times t jr & t jf 02ns trst assert time (2) ttrst 25 - ns input setup times: (3) boundary - scan data tms, tdi t dvjh t ivjh 4 0 - - ns input hold times: (3) boundary - scan data tms, tdi t dxjh t ixjh 15 12 - - ns valid times: (4) boundary - scan data tdo t jldv t jlov - - 4 4 ns output hold times: (4) boundary - scan data tdo t jldv t jlov 25 12 - - ns tck to output high impedance: (4)(5) boundary - scan data tdo t jldz t jloz 3 3 19 9 ns ov dd /2 output z 0 = 50 ? r l = 50 ?
33 2138e?hirel?01/05 pc755/745 atmel confidential figure 19 provides the jtag clock input timing diagram. figure 19. jtag clock input timing diagram figure 20 provides the trst timing diagram. figure 20. trst timing diagram figure 21 provides the boundary-scan timing diagram. figure 21. boundary-scan timing diagram tclk vm vm vm vm = midpoint voltage (ov dd /2 ) t tclk t jr t jf t jhjl trst t trst vm = midpoint voltage (ov dd /2) vm vm vm vm tck boundary boundary boundary data outputs data inputs data outputs vm = midpoint voltage (ov dd /2 ) t dxjh t dvjh t jldv t jldz input data vali d output t jldh data valid output data valid
34 2138e?hirel?01/05 pc755/745 atmel confidential figure 22 provides the test access port timing diagram. figure 22. test access port timing diagram jtag configuration signals boundary scan testing is enabled through the jtag interface signals. the trst signal is optional in the ieee 1149.1 specification, but is provided on all processors that implement the powerpc architecture. while it is possible to force the tap controller to the reset state using only the tck and tms signals, mo re reliable power-on reset performance will be obtained if the trst signal is asserted during power-on reset. be cause the jtag interface is also used for accessing the common on-chip processor (cop) function, simply tying trst to hreset is not practical. the cop function of these processors allows a remote computer system (typically, a pc with dedicated hardware and debugging software) to access and control the internal operations of the processor. the cop interface connects primarily through the jtag port of the processor, with some additional status monitoring signal s. the cop port requires the ability to indepen- dently assert hreset or trst in order to fully control the processor. if the target system has independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or push-button switches, then the cop reset signals must bemerged into these signals with logic. the arrangement shown in figure 23 allows the cop port to independently assert hreset or trst , while ensuring that th e target can drive hreset as well. if the jtag interface and cop header will not be used, trst should be tied to hreset through a 0 ? isolation resistor so that it is asserted when the systemreset signal (hreset ) is asserted ensuring that the jtag scan chain is initialized during power-on. while freescale recommends that the cop header be designed into the system as shown in figure 23 , if this is not possible, the isolation resistor will allow future access to trst in the case where a jtag interfacemay need to be wired onto the system in debug situations. the cop header shown in figure 23 adds many benefits ? breakpoints, watchpoints, register and memory examination/modification, and other standard debugger features are possible through this interface ? and can be as inexpensive as an unpopulated footprint for a header to be added when needed. the cop interface has a standard header for connection to the target system, based on the 0.025" square-post 0.100" centered header asse mbly (often called a berg header). the connec- tor typically has pin 14 removed as a connector key. tck tdi, tms tdo vm = midpoint voltage (ov dd /2) tdo vm vm t ixjh t ivjh t jlov t jloz input data vali d output t jloh data valid output data valid
35 2138e?hirel?01/05 pc755/745 atmel confidential figure 23. jtag interface connection notes: 1. run/stop , normally found on pin 5 of the cop header, is not implemented on the pc755. connect pin 5 of the cop header to ov dd with a 10 k ? pull-up resistor. 2. key location; pin 14 is not physi cally present on the cop header. 3. component not populated. populate only if debug tool does not drive qack . 4. populate only if debug tool uses an open-drain type output and does not actively deassert qack . 5. if the jtag interface is implemented, connect hreset from the target source to trst from the cop header though an and gate to trst of the part. if the jtag interface is not imple- mented, connect hreset from the target source to trst of the part through a 0 ? isolation resistor. hreset hreset from target board sources 13 sreset sreset sreset nc nc 11 vdd_sense 6 5 1 15 2k ? 10 k ? 10 k ? 10 k ? ov dd ov dd ov dd ov dd chkstp_in chkstp_in 8 tms tdo tdi tck tms tdo tdi tck 9 1 3 4 trst 7 16 2 10 12 (if any) cop header 14 2 key qack ov dd ov dd 10 k ? ov dd trst 10 k ? ov dd 10 k ? 10 k ? qack qack chkstp_out chkstp_out 3 13 9 5 1 6 10 2 15 11 7 16 12 8 4 key no pin cop connector physical pin out 10 k ? 4 ov dd 1 2k ? 3 0 ? 5 hreset
36 2138e?hirel?01/05 pc755/745 atmel confidential the cop header shown in figure 24 adds many benefits?breakpoints, watchpoints, register and memory examination/modification and other standard debugger features are possible through this interface ? and can be as inexpensive as an unpopulated footprint for a header to be added when needed. the cop interface has a standard header for connection to the target system, based on the 0.025? square-post 0.100? centered header asse mbly (often called a ?berg? header). the con- nector typically has pin 14 removed as a connector key. figure 24 shows the cop connector diagram. figure 24. cop connector diagram there is no standardized way to number the cop header shown in figure 24 ; consequently, many different pin numbers have been observed from emulator vendors. some are numbered top-to-bottom then left-to- right, while others use left-to-right then top-to -bottom, while still others number the pins counter clockwise from pin one (as with an ic). regardless of the numbering, the signal placement recommended in figure 24 is common to all known emulators. the qack signal shown in table 15 is usually hooked up to the pci bridge chip in a system and is an input to the pc755 informing it that it can go into the quiescent state. under normal opera- tion this occurs during a low power mode selection. in order for cop to work the pc755 must see this signal asserted (pulled down). while shown on the cop header, not all emulator prod- ucts drive this signal. to preserve correct power down operation, qack should be merged so that it also can be driven by the pci bridge. 3 ck stp_out 13 9 5 1 6 10 2 top view 15 11 7 16 12 8 4 key no pi n hreset sreset tm s run/st op tck tdi tdo ground trst vdd_sense pins 10, 12 and 14 are no-connects. pin 14 is not physically pres ent qack chkstp_ in
37 2138e?hirel?01/05 pc755/745 atmel confidential preparation for delivery packaging microcircuits are prepared for delivery in accordance with mil-prf-38535. certificate of compliance atmel offers a certificate of compliances with each shipment of parts, affirming the products are in compliance either with mil-prf-883 and guarantying the parameters not tested at tempera- ture extremes for the entire temperature range. handling mos devices must be handled with certain precautions to avoid damage due to accumulation of static charge. input protection devices have been designed in the chip to minimize the effect of static buildup. however, the followin g handling practices are recommended: 1. devices should be handled on benches with conductive and grounded surfaces 2. ground test equipment, tools and operator 3. do not handle devices by the leads 4. store devices in conductive foam or carriers 5. avoid use of plastic, rubber, or silk in mos areas 6. maintain relative humidity above 50 percent if practical 7. for ci-cga packages, use specific tray to take care of the highest height of the package compared with the normal cbga
38 2138e?hirel?01/05 pc755/745 atmel confidential clock relationship choices the pc755?s pll is configured by the pll_cfg[0-3] signals. for a given sysclk (bus) fre- quency, the pll configuration signals set the internal cpu and vco frequency of operation. the pll configuration for the pc755 is shown in figure 26 for example frequencies. notes: 1. pll_cfg[0:3] settings not listed are reserved. 2. the sample bus-to-core frequencies shown are for reference onl y. some pll configurations may select bus, core, or vco frequencies which are not useful, not suppor ted, or not tested for by the pc755; see ?clock ac specifications? on page 25 for valid sysclk, core, and vco frequencies. 3. in pll-bypass mode, the sysclk input signal clocks the internal processor directly, the pll is disabled, and the bus mode is set for 1:1 mode operation. this mode is in tended for factory use and emulator tool use only. note: the ac timing specifications given in th is document do not apply in pll-bypass mode. 4. in pll off mode, no clocking occurs inside the pc755 regardless of the sysclk input. table 16. pc755 microprocessor pll configuration pll_cfg [0-3] example bus-to-core frequency in mhz (vco frequency in mhz) bus-to-core multiplier core-to vco multiplier bus 33 mhz bus 50 mhz bus 66 mhz bus 75 mhz bus 80 mhz bus 100 mhz 0100 2x 2x ----- 200 (400) 1000 3x 2x - - 200 (400) 225 (450) 240 (480) 300 (600) 1110 3.5x 2x - - 233 (466) 263 (525) 280 (560) 350 (700) 1010 4x 2x - 200 (400) 266 (533) 300 (600) 320 (640) 400 (800) 0111 4.5x 2x - 225 (450) 300 (600) 338 (675) 360 (720) - 1011 5x 2x - 250 (500) 333 (666) 375 (750) 400 (800) - 1001 5.5x 2x - 275 (550) 366 5733 --- 1101 6x 2x 200 (400) 300 (600) 400 (800) --- 0101 6.5x 2x 216 (433) 325 (650) ---- 0010 7x 2x 233 (466) 350 (700) ---- 0001 7.5x 2x 250 (500) 375 (750) ---- 1100 8x 2x 266 (533) 400 (800) ---- 0110 10x 2x 333 (666) ----- 0011 pll off/bypass pll off, sysclk clocks core circuitry directly, 1x bus-to-core implied 1111 pll off pll off, no core clocking occurs
39 2138e?hirel?01/05 pc755/745 atmel confidential the pc755 generates the clock for the external l2 synchronous data srams by dividing the core clock frequency of the pc755. the divided-down clock is then phase-adjusted by an on- chip delay-lock-loop (dll) circuit and should be routed from the pc755 to the external rams. a separate clock output, l2sync_out is sent out half the distance to the srams and then returned as an input to the dll on pin l2sync_in so that the rising-edge of the clock as seen at the external rams can be aligned to the cl ocking of the internal latches in the l2 bus interface. the core-to-l2 frequency divisor for the l2 pll is selected through the l2clk bits of the l2cr register. generally, the divisor must be chosen according to the frequency supported by the external rams, the frequency of the pc755 core, and the phase adjustment range that the l2 dll supports. figure 18 shows various example l2 clock frequencies that can be obtained for a given set of core frequencies. the minimum l2 frequency target is 80 mhz. note: the core and l2 frequencies are for reference only. some examples may represent core or l2 frequencies which are not useful, not supported, or not tested for by the pc755; see ?l2 clock ac specifications? on page 28 for valid l2clk frequencies. the l2cr[l2sl] bit should be set for l2clk frequencies less than 110 mhz. table 17. sample core-to-l2 frequencies core frequency in mhz 1 1.5 2 2.5 3 250 250 166 125 100 83 266 266 177 133 106 89 275 275 183 138 110 92 300 300 200 150 120 100 325 325 217 163 130 108 333 333 222 167 133 111 350 350 233 175 140 117 366 366 244 183 146 122 375 375 250 188 150 125 400 400 266 200 160 133
40 2138e?hirel?01/05 pc755/745 atmel confidential system design information pll power supply filtering the av dd and l2av dd power signals are provided on the pc755 to provide power to the clock generation phase-locked loop and l2 cache delay-lo cked loop respectively. to ensure stability of the internal clock, the power supplied to the av dd input signal should be filtered of any noise in the 500 khz to 10 mhz resonant frequency range of the pll. a circuit similar to the one shown in figure 26 using surface mount capacitors with minimum effective series inductance (esl) is recommended. consistent with the recommendations of dr. howard johnson in high speed digital design: a handbook of black magic (prentice hall, 1993), multiple small capacitors of equal value are recommended over a single large value capacitor. the circuit should be placed as close as possible to the av dd pin to minimize noise coupled from nearby circuits. an identical but separate circuit should be plac ed as close as possible to the l2av dd pin. it is often possible to route directly from the capacitors to the av dd pin, which is on the periphery of the 360 bga footprint, without the inductance of vias. the l2av dd pin may be more difficult to route but is proportionately less critical. figure 25. pll power supply filter circuit power supply voltage sequencing the notes in figure 27 contain cautions about the sequencing of the external bus voltages and core voltage of the pc755 (when they are different). these cautions are necessary for the long term reliability of the part. if they are violated , the esd (electrostatic discharge) protection diodes will be forward bi ased and excessive current can flow through these diodes. if the system power supply design does not control the voltage sequencing, the circuit of figure 27 can be added to meet these requirements. the mur420 schottky diodes of figure 27 control the maxi- mum potential difference between the external bus and core power supplies on power-up and the 1n5820 diodes regulate the maximum potential difference on power-down. figure 26. example voltage sequencing circuit v dd av dd (or l2av dd ) 10 ? 2.2 f 2.2 f gnd low esl surface mount capacitors 3.3v 2.0v murs320 1n5820 murs320 1n5820
41 2138e?hirel?01/05 pc755/745 atmel confidential decoupling recommendations due to the pc755?s dynamic power management feature, large address and data buses, and high operating frequencies, the pc755 can generate transient power surges and high frequency noise in its power supply, especia lly while driving large capacitive loads. this noise must be pre- vented from reaching other co mponents in the pc755 system, an d the pc755 itself requires a clean, tightly regulated source of power. therefore, it is recommended that the system designer place at least one decoupling capacitor at each v dd , o v dd , and l2ov dd pin of the pc755. it is also recommended that these decoupling capacit ors receive their power from separate v dd , (l2)ov dd and gnd power planes in th e pcb, utilizing short traces to minimize inductance. these capacitors should have a value of 0.01 f or 0.1 f. only ceramic smt (surface mount technology) capacitors should be used to minimi ze lead inductance, preferably 0508 or 0603 ori- entations where connections are made along the length of the part. in addition, it is recommended that there be several bulk storage capacitors distributed around the pcb, feeding the v dd , l2o v dd , and ov vplanes, to enable quick recharging of the smaller chip capacitors. these bulk capacitors should ha ve a low esr (equivalent series resistance) rat- ing to ensure the quick response time necessar y. they should also be connected to the power and ground planes through two vias to minimize inductance. suggested bulk capacitors ? 100- 330 f (avx tps tantalum or sanyo oscon). connection recommendations to ensure reliable operation, it is highly recommended to connect unused inputs to an appropri- ate signal level through a resistor. unused active low inputs should be tied to o v dd . unused active high inputs should be connected to gnd. all nc (no- connect) signals must remain unconnected. power and ground connections must be made to all external v dd , o v dd , l2o v dd , and gnd pins of the pc755. output buffer dc impedance the pc755 60x and l2 i/o drivers are characterized over process, voltage, and temperature. to measure z 0 , an external resistor is connected from the chip pad to (l2)ov dd or gnd. then, the value of each resistor is varied until the pad voltage is (l2)o v dd /2 (see figure 28 ). the output impedance is the average of two components, the resistances of the pull-up and pull- down devices. when data is held low, sw2 is closed (sw1 is open), and r n is trimmed until the voltage at the pad equals (l2)o v dd /2. r n then becomes the resistance of the pull-down devices. when data is held high, sw1 is closed (sw2 is open), and r p is trimmed until the voltage at the pad equals (l2)o v dd /2. r p then becomes the resistance of the pull-up devices. no tag describes the driver impedance measurement circuit described above.
42 2138e?hirel?01/05 pc755/745 atmel confidential figure 27. driver impedance measurement circuit alternately, the following is another method to determine the output impedance of the pc755. a voltage source, v force , is connected to the output of the pc755 as in figure 28 . data is held low, the voltage source is set to a value that is equal to (l2)o v dd /2 and the current sourced by v force is measured. the voltage drop across the pull-down device, which is equal to (l2)o v dd /2, is divided by the measured current to determine the output impedance of the pull-down device, r n . similarly, the impedance of the pull-up device is determined by dividing the voltage drop of the pull-up, (l2)o v dd /2, by the current sank by the pull-up when the data is high and v force is equal to (l2)o v dd /2. this method can be employed with either empirical data from a test set up or with data from simulation models, such as ibis. r p and r n are designed to be close to each other in value. then z 0 = (r p + r n )/2. figure 28 describes the alternate driver impedance measurement circuit. figure 28. alternate driver impedance measurement circuit (l2)ov dd ognd r p r n pad data sw1 sw2 (l2)ov dd (l2)ov dd bga da ta pi n ognd vforce
43 2138e?hirel?01/05 pc755/745 atmel confidential table 18 summarizes the signal impedance results. the driver impedance values were charac- terized at 0 c, 65 c, and 105 c. the impedance increases with junction temperature and is relatively unaffected by bus voltage. pull - up resistor requirements the pc755 requires pull-up resistors (1 k ? ? 5 k ? ) on several control pins of the bus interface to maintain the control signals in the negated state after they have been actively negated and released by the processor or other bus masters. these pins are ts , abb , aack , artry , dbb , dbwo , ta , tea , and dbdis . drtry should also be connected to a pull-up resistor (1 k ? ? 5 k ? ) if it will be used by the system; otherw ise, this signal should be connected to hreset to select no-drtry mode. three test pins also require pull-up resistors (100 ? ? 1 k ? ). these pins are l1_tstclk, l2_tstclk, and lssd_mode . these signals are for factory use only and must be pulled up to ov dd for normal machine operation. in addition, ckstp_out is an open-drain style output that requires a pull-up resistor (1 k ? ? 5 k ? ) if it is used by the system. during inactive periods on the bus, the address and transfer attributes may not be driven by any master and may, therefore, float in the high-impedance state for relatively long periods of time. since the processor must continually monitor these signals for snooping, this float condition may cause additional power draw by the input receivers on the processor or by other receivers in the system. these signals can be pulled up through weak (10 k ? ) pull-up resistors by the system or may be otherwise driven by the system during inacti ve periods of the bus to avoid this additional power draw, but address bus pull-up resistors are not necessary for proper device operation. the snooped address and transfer attribute inputs are: a[0:31], ap[0:3], tt[0:4], tbst , and gbl . the data bus input receivers are normally turned off when no read operation is in progress and, therefore, do not require pull-up resistors on the bus. other data bus receivers in the system, however, may require pull-ups, or that those si gnals be otherwise driven by the system during inactive periods by the system. the data bus signals are: dh[0:31], dl[0:31], and dp[0:7]. if 32-bit data bus mode is sele cted, the input receivers of the unused data and parity bits will be disabled, and their outputs will driv e logic zeros when they would otherwise normally be driven. for this mode, these pins do not require pull-up resistors, and should be left unconnected by the system to minimize po ssible output switching. if address or data parity is not used by the sy stem, and the respective parity checking is disabled through hid0, the input receivers for those pins are disabled, and those pins do not require pull- up resistors and should be left unconnected by the system. if all parity generation is disabled through hid0, then all parity checking should also be disabled through hid0, and all parity pins may be left unconnected by the system. table 18. impedance characteristics. v dd = 2.0v, ov dd = 3.3v, t c = 0 - 105 c impedance processor bus l2 bus symbol unit rn 25-36 25-36 z 0 w rp 26-39 26-39 z 0 w
44 2138e?hirel?01/05 pc755/745 atmel confidential package mechanical data the following sections provide the package par ameters and mechanical dimensions for the pc745, 255 pbga package as well as the pc755, 360 cbga and pbga packages. while both the pc755 plastic and the ceramic packages are described here, both packages are not guaran- teed to be available at the same time. all new designs should allow for either ceramic or plastic bga packages for this device. for more information on designing a common footprint for both plastic and ceramic package types, please contact your local freescale sales office. package parameters for the pc745 the package parameters are as provided in the following list. the package type is 21 21 mm, 255-lead plastic ball grid array (pbga). table 19. package parameters parameter hitce pbga package outline 21 21 mm 21 21 mm interconnects 255 (16 16 ball array ? 1) 255 (16 16 ball array ? 1) pitch 1.27 mm (50 mil) 1.27 mm (50 mil) minimum module height 2.42 2.25 mm maximum module height 3.08 2.80 mm ball diameter (typical) 0.89 mm (35 mil) 0.75 mm (29.5 mil)
45 2138e?hirel?01/05 pc755/745 atmel confidential mechanical dimensions of the pc745 hitce package figure 30 provides the mechanical dimensions and bottom surface nomenclature of the pc745, 255 hitce package. figure 29. mechanical dimensions and bottom surface nomenclature of the pc745 hitce b c 255x e 12345678910111213141516 a b c d e f g h j k l m n p r t a 0.3 c 0.15 b notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. dimensions in millimeters. 3. top side a1 corner index is a metalized feature with various shapes. bottom side a1 corner is designated with a ball missing from the array. 4. capacitor pads may be unpopulated. dim min max a 2.42 3.08 a1 0.8 1.0 a2 0.90 1.14 a3 0.60 b 0.82 0.93 d d1 e e1 e 1.27 bsc 21.00 bsc 21.00 bsc 7.87 6.75 millimeters 0.2 d 2x a1 corner e 0.2 b a c 0.2 c e1 d1 a a1 a2 a3 1
46 2138e?hirel?01/05 pc755/745 atmel confidential mechanical dimensions of the pc745 pbga package figure 30 provides the mechanical dimensions and bottom surface nomenclature of the pc745, 255 pbga package. figure 30. mechanical dimensions and bottom surface nomenclature of the pc745 pbga package parameter for the pc755 the package parameters are as provided in the following list. the package type is 25 x 25 mm, 360-lead plastic ball grid array (pbga). b c 255x e 12345678910111213141516 a b c d e f g h j k l m n p r t a 0.3 c 0.15 b notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. dimensions in millimeters. 3. top side a1 corner index is a metalized feature with various shapes. bottom side a1 corner is designated with a ball missing from the array. 4. capacitor pads may be unpopulated. dim min max a 2.25 2.80 a1 0.50 0.70 a2 1.00 1.20 a3 0.60 b 0.60 0.90 d d1 e e1 e 1.27 bsc 21.00 bsc 21.00 bsc 7.87 6.75 millimeters 0.2 d 2x a1 corner e 0.2 b a c 0.2 c e1 d1 a a1 a2 a3 1 table 20. package parameters parameter hitce-cbga pbga package outline 25 mm 25 mm 25 mm 25 mm interconnects 360 (19 x 19 ball array ? 1) 360 (19 x 19 ball array ? 1 pitch 1.27 mm (50 mil) 1.27 mm (50 mil) minimum module height 2,65 mm 2.22 mm maximum module height 3,2 mm 2.77 mm ball diameter 0,89 mm (35 mil) 0.75 mm (29.5 mil)
47 2138e?hirel?01/05 pc755/745 atmel confidential mechanical dimensions of the pc755 pbga figure 31 provides the mechanical dimensions and bottom surface nomenclature of the pc755, 360 pbga package. figure 31. mechanical dimensions and bottom surface nomenclature of the pc755 pbga notes: 1. dimensioning and tolerancing per asme y14.5m, 1994 2. dimensions in millimeters 3. top side a1 corner index is a metalized feature with various shapes. bottom side a1 corner is designated with a ball missing from the array 0.2 360x d 2x a1 corner e e 0.2 2x b a 12345678910111213141516 a b c d e f g h j k l m n p r t b c 0.2 c 171819 u w v millimeters dim min max a 2.22 2.77 a1 0.50 0.70 a2 1.00 1.20 a3 ?0.60 b 0.60 0.90 d 25.00 bsc d1 6.75 e 25.00 bsc e1 7.87 e 1.27 bsc e1 d1 a a1 a2 a3 1 b c a 0.3 c 0.15
48 2138e?hirel?01/05 pc755/745 atmel confidential mechanical dimensions of the pc755 cbga package figure 33 provides the mechanical dimensions and bottom surface nomenclature of the pc755, 360 cbga package. figure 32. mechanical dimensions and bottom surface nomenclature of pc755 (cbga) b c 360x e 12345678910111213141516 a b c d e f g h j k l m n p r t a 0.3 c 0.15 b a a1 a2 c c 171819 u w v millimeters dim min max a 2.65 3.20 a1 0.79 0.99 a2 1.10 1.30 a3 ?0.60 b 0.82 0.93 d 25.00 bsc d1 6.75 e 25.00 bsc e1 7.87 e 1.27 bsc 0.2 d 2x a1 corner e 0.2 2x a e1 d1 a3 1 0.15 b notes: 1. dimensioning and tolerancing per asme y14.5m, 1994 2. dimensions in millimeters 3. top side a1 corner index is a metalized feature with various shapes. bottom side a1 corner is designated with a ball missing from the array
49 2138e?hirel?01/05 pc755/745 atmel confidential mechanical dimensions of the pc755 hitce package figure 33 provides the mechanical dimensions and bottom surface nomenclature of the pc755, 360 hitce package. figure 33. mechanical dimensions and bottom surface nomenclature of pc755 (hitce) b c 360x e 12345678910111213141516 a b c d e f g h j k l m n p r t a 0.3 c 0.15 b a a1 a2 c 0.15 c 171819 u w v millimeters dim min max a 2.65 3.24 a1 0.79 0.99 a2 1.10 1.30 a3 ?0.60 b 0.82 0.93 d 25.00 bsc d1 6.75 e 25.00 bsc e1 7.87 e 1.27 bsc 0.2 d 2x a1 corner e 0.2 2x a e1 d1 a3 1 b notes: 1. dimensioning and tolerancing per asme y14.5m, 1994 2. dimensions in millimeters 3. top side a1 corner index is a metalized feature with various shapes. bottom side a1 corner is designated with a ball missing from the array
50 2138e?hirel?01/05 pc755/745 atmel confidential mechanical dimensions of the pc755 ci-cga package figure 34 provides the mechanical dimensions and bottom surface nomenclature of pc755, 360 ci-cga package. figure 34. mechanical dimensions and bottom surface nomenclature of pc755 (ci-cga) b c 360x e 12345678910111213141516 a b c d e f g h j k l m n p r t a 0.3 c 0.15 b a a4 a2 171819 u w v millimeters dim min max a 4.04 bsc a1 a2 1.10 1.30 1.545 1.695 a3 ?0.60 b 0.79 0.990 d 25.00 bsc d1 6.75 e 25.00 bsc e1 7.87 e 0.2 d 2x a1 corner e 0.2 2x a e1 d1 a3 a1 a6 a5 a4 0.82 0.9 a5 0.10 bsc a6 0.25 0.35 1.27 bsc b notes: 1. dimensioning and tolerancing per asme y14.5m, 1994 2. dimensions in millimeters 3. top side a1 corner index is a metalized feature with various shapes. bottom side a1 corner is designated with a ball missing from the array c b 0.15
51 2138e?hirel?01/05 pc755/745 atmel confidential ordering information note: for availability of different versions, contact your atmel sales office. c pcx745 pcx755 m zf u 300 l x type package: zf: fc-pbga screening level (1) u: upscreening test revision level (1) e: rev. 2.8 temperature range: tj m: -55 c, +125 c v: -40 c, +110 c bus divider (to be confirmed) l: any valid pll configuration max internal processor speed 300: 300 mhz 350: 350 mhz 366: 366 mhz 400: 400 mhz type package: g: cbga gs: ci-cga gh: hitce screening level (1) u: upscreening test blank: standard revision level (1) e: rev. 2.8 temperature range: tj m: -55 c, +125 c v: -40 c, +110 c bus divider (to be confirmed) l: any valid pll configuration max internal processor speed 300: 300 mhz 350: 350 mhz 366: 366 mhz 400: 400 mhz pc745 pc755 m gh u 300 l x c b for 300, 350, 366 mhz c for 400 mhz b for 300, 350, 366 mhz c for 400 mhz
52 2138e?hirel?01/05 pc755/745 atmel confidential definitions life support applications these products are not designed for use in life support applian ces, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. atmel customers using or selling these prod ucts for use in such applicatio ns do so at their own risk and agree to fully indemnity atmel for any damages resulting from such improper use or sale. differences with commercial part document revision history table 19 provides a revision histor y for this hardware specification. datasheet status validity objective specification this datasheet contai ns target and goal specifications for discussion with the customer and application validation before design phase. target specification this da tasheet contains target or goal specifications for product development valid during the design phase. preliminary specification site this datasheet contains preliminary data. additional data may be published later; could include simulation result valid before characterization phase. preliminary specification site this datasheet also contains characterization results valid before the industrialization phase. product specification this datasheet contains final product specifications valid for production purpose. limiting values limiting values given are in accordance with the absolute maxi mum rating system (iec 134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sect ions of the specification is not implied. exposure to limitin g values for extended periods may affect device reliability. application information where application information is given, it is advis ory and does not form part of the specification. commercial part military part temperature range t j = 0 to 105 ct j = - 55 c to 125 c table 21. revision history revision number date substantive change(s) 2138e 10/2004 product specification release subs equent to product qualification motorola changed to freescale 2138d 06/2003 preliminary -site
i 2138e?hirel?01/05 pc755/745 atmel confidential table of contents features .............. .............. .............. .............. .............. .............. ............1 description ......... .............. .............. .............. .............. .............. ............1 screening ........... .............. .............. .............. .............. .............. ............2 general description .......... .............. .............. .............. .............. ..........2 simplified block diagram ...................................................................................... 2 general parameters ............................................................................................. 3 features ............................................................................................................... 3 pin assignments ............... .............. .............. .............. .............. ..........6 pinout listings ...................................................................................................... 8 signal description ............... ................. ................ ................. ............13 detailed specifications ....... ................. ................ ................. ............14 applicable documents ........ ................. ................ ................. ............14 design and construction .................................................................................... 14 terminal connections ................................................................................. 14 absolute maximum ratings (1) ..................................................................... 14 recommended operating conditions (1) ...................................................... 16 thermal characteristics ......... ................ ................. ................ ..........17 package characteristics ..................................................................................... 17 package thermal characteristics for hitce .............................................. 17 thermal management assistance .............................................................. 19 thermal management information .............................................................. 19 adhesives and thermal interface materials ................................................ 20 heat sink selection example ...................................................................... 20 power consideration ........... ................. ................ ................. ............22 power management ........................................................................................... 22 power dissipation ............................................................................................... 23 electrical characteristics .... ................. ................ ................. ............24 static characteristics .......................................................................................... 24 dynamic characteristics ..................................................................................... 25 clock ac specifications .............................................................................. 25 ieee 1149.1 ac timing specifications ....................................................... 32 preparation for delivery ...... ................. ................ ................. ............37 packaging ........................................................................................................... 37
ii 2138e?hirel?01/05 pc755/745 atmel confidential certificate of compliance ................................................................................... 37 handling ............................................................................................................. 37 clock relationship choices ................................................................................ 38 system design information ..... ................ ................. .............. ..........40 pll power supply filtering ................................................................................ 40 power supply voltage sequencing .................................................................... 40 decoupling recommendations ........................................................................... 41 connection recommendations .......................................................................... 41 output buffer dc impedance ............................................................................. 41 pull-up resistor requirements ........................................................................... 43 package mechanical data ... ................. ................ ................. ............44 package parameters for the pc745 ................................................................... 44 mechanical dimensions of the pc745 hitce package ............................. 45 mechanical dimensions of the pc745 pbga package .............................. 46 package parameter for the pc755 ..................................................................... 46 mechanical dimensions of the pc755 pbga ............................................. 47 mechanical dimensions of the pc755 cbga package .............................. 48 mechanical dimensions of the pc755 hitce package ............................. 49 mechanical dimensions of the pc755 ci-cga package ........................... 50 ordering information ........... ................. ................ ................. ............51 definitions .......... .............. .............. .............. .............. .............. ..........52 life support applications .................................................................................... 52 differences with commercial part ...................................................................... 52 document revision history ... ................ ................. ................ ..........52
printed on recycled paper. atmel confidential 2138e?hirel?01/05 xm ? atmel corporation 2005 . all rights reserved. atmel ? , logo and combinations thereof are the regi stered trademarks of atmel corporation or its subsidiaries. powerpc ? is the registered trademark of ibm corp. freescale is the registered trademark of freescale, inc. altivec ? is a trade- mark of freescale, inc. other terms and product names may be trademarks of others. disclaimer: the information in this document is provided in connection with atmel products. no license, expr ess or implied, by estoppel or otherwise, to any intellectual property right is grant ed by this document or in connection with the sale of atmel products. except as set forth in atmel?s terms and condi- tions of sale located on atmel?s web site, atmel assumes no li ability whatsoever and disclaims any express, implied or statutor y warranty relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particu lar purpose, or non-infringement. in no event shall atmel be liable for any direct, indirect, consequentia l, punitive, special or i nciden- tal damages (including, without limitation, dam ages for loss of profits, business interr uption, or loss of information) arising out of the use or inability to use this document, even if atmel has been advis ed of the possibility of such damages. atmel makes no representations or warranties with respect to the accuracy or co mpleteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. atmel does not make any commitment to update the information contained her ein. atmel?s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. atmel corporation atmel operations 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 487-2600 regional headquarters europe atmel sarl route des arsenaux 41 case postale 80 ch-1705 fribourg switzerland tel: (41) 26-426-5555 fax: (41) 26-426-5500 asia room 1219 chinachem golden plaza 77 mody road tsimshatsui east kowloon hong kong tel: (852) 2721-9778 fax: (852) 2722-1369 japan 9f, tonetsu shinkawa bldg. 1-24-8 shinkawa chuo-ku, tokyo 104-0033 japan tel: (81) 3-3523-3551 fax: (81) 3-3523-7581 memory 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 microcontrollers 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 la chantrerie bp 70602 44306 nantes cedex 3, france tel: (33) 2-40-18-18-18 fax: (33) 2-40-18-19-60 asic/assp/smart cards zone industrielle 13106 rousset cedex, france tel: (33) 4-42-53-60-00 fax: (33) 4-42-53-60-01 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 scottish enterprise technology park maxwell building east kilbride g75 0qr, scotland tel: (44) 1355-803-000 fax: (44) 1355-242-743 rf/automotive theresienstrasse 2 postfach 3535 74025 heilbronn, germany tel: (49) 71-31-67-0 fax: (49) 71-31-67-2340 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 biometrics/imagin g/hi-rel mpu/ high speed converters/rf datacom avenue de rochepleine bp 123 38521 saint-egreve cedex, france tel: (33) 4-76-58-30-00 fax: (33) 4-76-58-34-80 literature requests www.atmel.com/literature

▲Up To Search▲

Price & Availability of PC755BMGS300LE

	To Download PC755BMGS300LE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .